+1(310)905-0006

Rockford Fosgate Punch P600X4 4-channel car amplifier 75 watts RMS x 4

Big power for your speakers or subwoofers
Rockford Fosgate's Punch P600X4 amplifier can put out 75 watts RMS to each of your front and rear speakers, plenty of power for clean music even at high levels. You can use the amp's high-pass filter to remove low bass from your speakers so they'll play more efficiently. You can also switch this amp into 2-channel mode to drive a couple of subwoofers with up to 300 watts RMS each. The amp's low-pass filter comes in handy for getting the right sound from your sub/enclosure combo. The Punch EQ2 includes bass and treble boosts, in case you want to add some boom and sizzle back into the mix.

Easy to set for optimum performance
Once again, Rockford Fosgate steps away from the crowd with their C.L.E.A.N. technology (Calibrated Level Eliminates Audible Noise) — a setup system that ensures your music will sound as clean and powerful as possible. It works like this: first download the setup tones from Rockford Fosgate, then play the tone, adjust the receiver volume until a red clip light on the amp goes out, then turn the amp gain up until a blue light comes on. It's that simple — your amplifier will be perfectly set to match your receiver's output. When your receiver reaches maximum clean volume, you'll get maximum clean power from your Power amp. At quiet listening levels, you'll hear less background noise and more of your music.

Keeps an eye on things while playing
If that blue light turns solid red while you're playing music, the amp's telling you that your source is distorting and you should turn it down, or risk damage to your gear. The optional PLC2 remote level control also doubles as a clip indicator, so you can see from the front seat if your music's clipping. The amp's built-in computer keeps tabs on the output current, ensuring that plunging speaker impedances (they change during play) or even a short circuit won't hurt anything.

Maintaining coolness raises efficiency and lowers distortion
Rockford Fosgate's Dynamic Thermal Management system uses forced air to dissipate heat evenly across the amp and out through the high-mass heatsink, efficiently drawing heat away from vital internal parts. Their proprietary MEHSA cooling process maximizes the heat transfer from the MOSFET devices to the heatsink, allowing the heat to escape more readily, so the transistors stay cooler and work better.

Product highlights:

• 4-channel car amplifier
• 75 watts RMS x 4 at 4 ohms (150 watts RMS x 4 at 2 ohms)
• 300 watts RMS x 2 bridged at 4 ohms (4-ohm stable in bridged mode)
• CEA-2006 compliant

• variable high- and low-pass filter filter (50-250 Hz, 12 dB/octave)
• variable PEQ2 bass/treble boost (0-18 dB at 45 Hz and 0-14 dB at 12.5K Hz)
• C.L.E.A.N. gain setup system includes clip lights and link to Rockford Fosgate's setup tones
• Class-AB amplifier design
• frequency response: 20-20K Hz
• Dynamic Thermal Management and MEHSA MOSFET cooling systems
• MOSFET power and output stages
• preamp inputs and outputs
• speaker-level inputs (speaker wire to RCA adapter required)
• signal-sensing turn-on with speaker-level inputs eliminate need for remote turn-on lead

• optional PLC2 wired remote level control with clip light available
• 4-gauge power and ground leads and an 100-amp fuse recommended — wiring and hardware not included with amplifier
• no onboard fuses — when installing multiple amps in a system, an additional 100-amp in-line fuse between the distribution block and the amplifier is recommended
• 13-3/8"W x 2-7/16"H x 8-13/16"D
• warranty: 1 year

⚠️Warning: